Iscar right now offers a family of high-performance slitting tools that incorporate the convenience and security of Tang-Grip clamping with the increased sturdiness of the completely new Sumo Tec insert grades.

The perception, already validated successful in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanied by a specific hand tool, and are held tightly in place without having the need without requiring clamps, upper jaws or set screws that can weaken the insert and disrupt chip flow. The pocket composition uses cutting forces to keep the insert seated firmly in position, preventing any risk of insert pull-out. The Tang-Grip clamping system also fosters additional accurate slitting cuts plus increased pocket and insert lifespan.

Iscar's Sumo Tec insert grades showcase a distinct post-coating treatment which substantially improves tool life and dependability.

Unveiled in late '07, the revolutionary Sumo Tec treatment flattens the insert's coated surface to dispose of microscopic stress raisers, lessen heat and friction and boost chip flow. The result is improved toughness and resistance to chipping and built-up edge, all leading to greater tool lifespan. The golden-colored flank on Sumo Tec inserts eases wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, permitting higher feed rates.

Their superior rigidity leads to straighter, better accurate cuts and less vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same assortment of inserts as Tang-Grip parting tools. Additional sizes will be added.

Obtainable Sumo Tec grades for Tangslit cutters include:
IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, providing extraordinary resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel.

IC830, offering additional toughness for heavier parting & grooving involving interrupted cuts. It is suited for any stainless steel & high temperature alloys.

IC908, a hard, fine-grain substrate with extraordinary chipping resistance, mixed with a new Sumo Tec TiAlN PVD coating. It is ideal for nodular or gray cast iron.

IC928 and 928A, PVD TiAlN-coated tough grades suited for stainless steel, high temperature alloys and other alloy steels. These grades are also favored for interrupted cuts and heavy operations.

Each Tangslit and Tang-Grip inserts are attainable in J- or C-type chipformer geometries from Iscar.

Iscar Recently Releases A Variety Of Brand New Lines To Increase Their Family Of Milling Cutters
Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries.

Some Of The Countless Improvements In Carbide Inserts From Iscar From Over The Last Decade
Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance.

Iscar Adds Their Most Recent Innovations To A Lengthy Line Of Effective Hole Producing Solutions
Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user.

Brand New Cutters And Carbide Insert Shapes From Iscar To Better Maximize The Machining Method
Iscar is introducing Penta 34 carbide inserts with a new PB chipformer. The PB chipformer features a single cavity with a positive rake, neutral shoulder angle, and a honed edge. It is actually a C-type chipformer with a different frontal edge.

The Most Recent In Carbide Endmill Configuration In A Lengthy And Prospering Family From Iscar
Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling.

Commercial Water Heater - Considering All Of Your Needs - Study Cautiously To Know More
Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit.

Some Of The Countless Improvements In Carbide Inserts From Iscar From Over The Last Decade

A Number Of Developments Have Enhanced Iscar's Line Of Indexable Endmills For Expanded Productivity

Iscar Adds Their Most Recent Innovations To A Lengthy Line Of Effective Hole Producing Solutions

Brand New Cutters And Carbide Insert Shapes From Iscar To Better Maximize The Machining Method

Brand New End Mills Coming From Iscar Can Multiply Productivity While Lowering Costs

Iscar Announces A Brand New Family Of Slitting Cutters Utilizing Tang-Grip Technology And The Sturdiness Of Sumo Tec Grades

Iscar Offers A Completely New Line Of Slitting Cutters Using Tang-Grip Technology And The Durability Of Sumo Tec Grades

Iscar Offers A Completely New Line Of Slitting Cutters Applying Tang-Grip Technology And The Strength Of Sumo Tec Grades

Iscar Releases A New Line Of Slitting Cutters Applying Tang-Grip Technology And The Durability Of Sumo Tec Grades

Some Of Advancements In Carbide Inserts Coming From Iscar

Some Of Advancements In Carbide Inserts By Iscar

A Couple Of The Numerous Advancements In Carbide Inserts From Iscar From Over The Last Decade

Carbide Drills

Fibroids Free Forever